Dongguan, Guangdong, China — Dongguan HX Fiber Technology Co., Ltd. (HXFiber) has released the HX-GQJG-13, a stainless steel armored fiber optic cable built on G657A2 bend-insensitive fiber. The cable pairs a spiral stainless steel armor tube with a 500N short term tensile rating, targeting indoor and outdoor links where rodent damage, tight bends and mechanical stress occur together.
The launch responds to a consistent pattern in export inquiries: contractors are moving away from conduit-heavy designs toward direct armored cable, but they need a construction that survives both the installation pull and years of exposure to humidity, salt air and gnawing animals.
The HX-GQJG-13 uses a spiral stainless steel armored tube as its primary mechanical barrier, rather than the aluminum tape or galvanized corrugated steel common in budget armored cables. Stainless steel resists corrosion and oxidation far better than zinc-coated alternatives, which is decisive in coastal, underground, mining and industrial environments where conventional armor can fail within a few years.
The same tube forms a continuous physical shield against rodents — one of the most common causes of unexplained link loss in duct, wall cavity and ceiling installations. In practice this removes the need to over-specify conduit or add secondary protection in rodent-prone sites, simplifying the bill of materials and reducing installed cost.
Installation is where cables fail. During duct pulling, riser drops and tray routing, a cable is briefly exposed to loads several times higher than its permanent working tension. The HX-GQJG-13 is rated at 500N short term tensile and 300N long term tensile, giving installers a working margin instead of a limit to gamble on.
The practical effects for contractors are concrete:
| Model Number | HX-GQJG-13 |
| Armored Tube Material | Stainless Steel (spiral armored protection) |
| Fiber Type | OM1 / OM2 / OM3 / OM4 / G652D / G657A1 / G657A2 |
| Fiber Mode | Singlemode, Multimode |
| Number of Cores | 1–48 core |
| Fiber Diameter | 9/125 µm, 62.5/125 µm, 50/125 µm |
| Short Term Tensile | 500N |
| Long Term Tensile | 300N |
| Dynamic Bending Radius | 10D |
| Static Bending Radius | 20D |
| Cable Loss | 850nm ≤ 3.5 dB/km; 1300nm ≤ 1.5 dB/km |
| Outer Sheath Material | PVC, LSZH, PU, PE |
| Cable OD | 3.0 / 4.0 / 5.0 / 6.0 / 7.0 / 8.0 mm |
| Working Temperature | -20°C to +70°C |
| Minimum Order Quantity | 1,000 |
Inside the armor, G657A2 bend-insensitive fiber keeps attenuation stable through the tight radii that real buildings impose: 10D dynamic and 20D static bending radius means the cable can follow a corner in a riser shaft or a wall cavity without a splice box. Attenuation stays at 850nm ≤ 3.5 dB/km and 1300nm ≤ 1.5 dB/km, and sheath options of PVC, LSZH, PU and PE let the same construction serve plenum-class indoor routes, outdoor duct runs and abrasive industrial floors.
Dongguan HX Fiber Technology Co., Ltd. brings about 15 years of manufacturing experience to this program. The company is a national high-tech enterprise and has been recognized as a Guangdong contract-abiding and credit-worthy enterprise and a Guangdong excellent enterprise unit.
Its 10,000 square meter factory produces 60,000 kilometers of fiber optic cable, 2 million patch cord connectors and assembles 15 million patch cords every month. Products support indoor and outdoor integrated cabling for China Mobile, China Telecom and China Unicom networks, fiber optic networks, power networks, high-speed rail, medical, mining and military applications, and are exported to the United States, Canada, Spain, Italy, France, Brazil, Colombia, Australia and Saudi Arabia.
R&D, production and customization sit under one roof. That is what allows non-standard constructions — sheath compound, core count, armor type, cable diameter, pre-terminated assemblies — to move from inquiry to sample without a third party in between.
Minimum order quantity is 1,000 units, with indicative pricing from CN¥0.5514 to CN¥0.6892 depending on core count, fiber grade and sheath material. Custom cable diameters from 3.0 mm to 8.0 mm and pre-terminated assemblies are available on request.
For datasheets, samples and project quotations, contact the HXFiber export team.
Dongguan, Guangdong, China — Dongguan HX Fiber Technology Co., Ltd. (HXFiber) has released the HX-GQJG-13, a stainless steel armored fiber optic cable built on G657A2 bend-insensitive fiber. The cable pairs a spiral stainless steel armor tube with a 500N short term tensile rating, targeting indoor and outdoor links where rodent damage, tight bends and mechanical stress occur together.
The launch responds to a consistent pattern in export inquiries: contractors are moving away from conduit-heavy designs toward direct armored cable, but they need a construction that survives both the installation pull and years of exposure to humidity, salt air and gnawing animals.
The HX-GQJG-13 uses a spiral stainless steel armored tube as its primary mechanical barrier, rather than the aluminum tape or galvanized corrugated steel common in budget armored cables. Stainless steel resists corrosion and oxidation far better than zinc-coated alternatives, which is decisive in coastal, underground, mining and industrial environments where conventional armor can fail within a few years.
The same tube forms a continuous physical shield against rodents — one of the most common causes of unexplained link loss in duct, wall cavity and ceiling installations. In practice this removes the need to over-specify conduit or add secondary protection in rodent-prone sites, simplifying the bill of materials and reducing installed cost.
Installation is where cables fail. During duct pulling, riser drops and tray routing, a cable is briefly exposed to loads several times higher than its permanent working tension. The HX-GQJG-13 is rated at 500N short term tensile and 300N long term tensile, giving installers a working margin instead of a limit to gamble on.
The practical effects for contractors are concrete:
| Model Number | HX-GQJG-13 |
| Armored Tube Material | Stainless Steel (spiral armored protection) |
| Fiber Type | OM1 / OM2 / OM3 / OM4 / G652D / G657A1 / G657A2 |
| Fiber Mode | Singlemode, Multimode |
| Number of Cores | 1–48 core |
| Fiber Diameter | 9/125 µm, 62.5/125 µm, 50/125 µm |
| Short Term Tensile | 500N |
| Long Term Tensile | 300N |
| Dynamic Bending Radius | 10D |
| Static Bending Radius | 20D |
| Cable Loss | 850nm ≤ 3.5 dB/km; 1300nm ≤ 1.5 dB/km |
| Outer Sheath Material | PVC, LSZH, PU, PE |
| Cable OD | 3.0 / 4.0 / 5.0 / 6.0 / 7.0 / 8.0 mm |
| Working Temperature | -20°C to +70°C |
| Minimum Order Quantity | 1,000 |
Inside the armor, G657A2 bend-insensitive fiber keeps attenuation stable through the tight radii that real buildings impose: 10D dynamic and 20D static bending radius means the cable can follow a corner in a riser shaft or a wall cavity without a splice box. Attenuation stays at 850nm ≤ 3.5 dB/km and 1300nm ≤ 1.5 dB/km, and sheath options of PVC, LSZH, PU and PE let the same construction serve plenum-class indoor routes, outdoor duct runs and abrasive industrial floors.
Dongguan HX Fiber Technology Co., Ltd. brings about 15 years of manufacturing experience to this program. The company is a national high-tech enterprise and has been recognized as a Guangdong contract-abiding and credit-worthy enterprise and a Guangdong excellent enterprise unit.
Its 10,000 square meter factory produces 60,000 kilometers of fiber optic cable, 2 million patch cord connectors and assembles 15 million patch cords every month. Products support indoor and outdoor integrated cabling for China Mobile, China Telecom and China Unicom networks, fiber optic networks, power networks, high-speed rail, medical, mining and military applications, and are exported to the United States, Canada, Spain, Italy, France, Brazil, Colombia, Australia and Saudi Arabia.
R&D, production and customization sit under one roof. That is what allows non-standard constructions — sheath compound, core count, armor type, cable diameter, pre-terminated assemblies — to move from inquiry to sample without a third party in between.
Minimum order quantity is 1,000 units, with indicative pricing from CN¥0.5514 to CN¥0.6892 depending on core count, fiber grade and sheath material. Custom cable diameters from 3.0 mm to 8.0 mm and pre-terminated assemblies are available on request.
For datasheets, samples and project quotations, contact the HXFiber export team.